Resources / Technical Articles
Technical Articles for Humidity-Control Decisions
Browse application notes, engineering explanations, equipment comparisons, and practical guidance for agriculture, energy, electrical, and industrial environments.
Use the article library to understand a technical question, then return to the resource center for cases, product information, video, and project-preparation material.
Start with the operating condition behind the question. Technical-reading scene. Explore application notes, selection guidance and engineering explanations.
BROWSE ARTICLE TOPICS
Start with the application or equipment context
01
Agriculture & Controlled Environments
Application notes and selection guidance for greenhouses, indoor cultivation rooms, drying spaces, and storage environments where humidity affects the crop rather than the building.
Browse articles → 02Industrial Dehumidification
Comparisons and engineering notes covering refrigerant, ceiling-mounted, desiccant, and low-dew-point equipment, and the operating conditions that decide between them.
Browse articles → 03Energy Storage & Electrical Environments
Guidance on dew point, condensation risk, compact installation, controls, and validation for battery energy storage, cabinets, containers, and switchgear.
Browse articles → 04Commercial & Building Moisture Control
Practical guidance on condensation, water damage, drying, mold prevention, and equipment choices for commercial spaces and building moisture problems.
Browse articles → 05Humidification & Air Quality
Technical articles on humidification, ventilation, filtration, humidity measurement, and how moisture control interacts with wider air systems.
Browse articles → 06Humidity Science & Engineering
Explanations of relative humidity, dew point, condensation, moisture measurement, monitoring, and controls for industrial humidity-control decisions.
Browse articles →TECHNICAL ARTICLE LIBRARY
Search, filter, and continue from the topic relevant to your work
Each article has a clear place in the resource library and connects to relevant industries, product families, cases, and project support.
FIND THE RIGHT RESOURCE
Search article titles, summaries, categories, and technical topics.
Search across the resource library.
Industrial Drying Rooms: Types, Setup and Sizing
Design an industrial material drying room from the product endpoint: calculate water load, distribute air through the wet load, select equipment and verify a representative batch.
Moisture Barriers and Vapor Retarders in Construction: What Each Layer Does
Distinguish water, air and vapor control layers before choosing a building membrane. Check the moisture path, climate, assembly and drying direction.
Crawl Space Humidity Control Solutions
Diagnose water, ground vapor and humid air before choosing crawl-space ventilation, sealing or dehumidification; review safety and code constraints.
How Long Does It Take for Water to Evaporate?
Estimate water evaporation and material drying from measured loss, room moisture balance and a material-specific endpoint—not a fixed clock or product nameplate.
Temperature and Humidity Data Logger Systems: Selection and Use
Select temperature and humidity data loggers by the monitoring task, measurement uncertainty, sensor location, sample interval, alarm response and record requirements.
VPD Chart: How to Read It, Calculate It and Use It
Read a temperature-by-RH VPD table, reproduce the calculation, and distinguish air VPD from the leaf-to-air difference.
Free Cooling in Data Centers: Types, Benefits and Humidity Limits
Compare direct air-side, indirect air-side and water-side data-center free cooling by heat path, climate, IT limits, humidity exposure and whole-system energy and water use.
Evaporative Cooling Efficiency: How to Calculate It and When It Works
Evaporative cooling effectiveness compares actual supply-air cooling with the entering dry-bulb to wet-bulb temperature gap. Check incoming climate, moisture added by direct stages, ventilation and the separate humidity target.
Using a Dehumidifier After a Water Leak: Setup, Run Time and Mold Prevention
Use dehumidifiers after a water leak as part of a contractor drying plan: assess hazards, extract water, plan airflow and drainage, then verify affected materials.
Choosing the Best Moisture Barrier for Concrete Floors
Compare below-slab vapor retarders, surface moisture mitigation and environmental drying by source, slab tests, flooring limits and installation constraints.
CO₂ Uptake in Photosynthesis: Enrichment, Airflow and the Humidity Trade-off
An aisle CO₂ reading does not establish what leaves receive or which factor limits crop response. Review light, source supply, canopy air, airflow, stomatal conditions and internal diffusion with synchronized measurements.
How Long Does Drywall Take to Dry?
Drywall drying time depends on compound type or water-damaged board conditions. Contractors need separate finishing, cavity-drying and material-acceptance checks.
NO MATCHING RESOURCES
Try a broader term or describe the application differently.
Search by equipment type, humidity issue, industry, installation condition, or a technical topic.
APPLY THE INFORMATION
Need help applying an article to a real project?
Share the application, operating conditions, target, and installation limits. We can help identify the questions that matter before product selection or engineering review.
Discuss Your Requirement