Wind power desiccant dehumidifier – 2.5 kg/h rated moisture removal
ADS-500M is a desiccant dehumidifier for wind-power, grid and substation environments. Its published moisture-removal rating is 2.5 kg/h at 20 °C and 60% RH; final selection should be confirmed against the actual temperature, humidity or dew-point target, airflow, filtration, regeneration-air and installation conditions.
Product selection should be confirmed against temperature, target humidity, airflow, drainage, power supply, and installation conditions.
DEFINITION
What is an industrial dehumidifier?
An industrial dehumidifier is a humidity-control device that removes water vapor from ambient or process air and holds relative humidity at a defined operating level. Industrial models are specified against the operating temperature, target humidity, airflow, drainage, and power supply of a project rather than by floor area alone.
ADS-500M is a Wind Power Dehumidifier unit with a published rated capacity of 2.5 kg/h on this page.
Yakeclimate designs and manufactures industrial dehumidification equipment for complex climate applications, with a focus on agriculture and energy projects.
Product overview
What ADS-500M is designed to do
ADS-500M is a desiccant dehumidifier for wind-power, grid and substation environments. Its published moisture-removal rating is 2.5 kg/h at 20 °C and 60% RH; final selection should be confirmed against the actual temperature, humidity or dew-point target, airflow, filtration, regeneration-air and installation conditions.
01
2.5 kg/h rated moisture removal at 20 °C and 60% RH
02
Published operating range from -30 °C to +50 °C
03
Separate process-air and regeneration-air paths
04
G4, F7 and H11 filtration listed for both air streams
05
Dry-contact control-board interface
Technical data
Product specifications
Values below are retained from the current product record. Final configuration should be confirmed in the project quotation.
Specification
Unit
ADS-500M
Dehumidification Capacity (20°C/60% RH)
kg/h
2.5
Operating Temperature
°C
-30–+50
Process Airflow
m³/h
550
Regeneration Airflow
m³/h
155
Rated Power
W
3700
Power Supply
V/Hz
AC 220V 50Hz
Rated Current
A
17
Process Air Filter
—
G4 / F7 / H11
Regeneration Air Filter
—
G4 / F7 / H11
Control
—
Dry-contact control board
Machine Dimensions (L×W×H)
mm
742 × 521 × 795
Net Weight
kg
65
TECHNOLOGY COMPARISON
Refrigerant versus desiccant rotor technology
The ADS-500M on this page is a Wind Power Dehumidifier unit; compare its published ratings in the specification table with the working principles below.
Technology route
How it works
Typical applications
Refrigerant dehumidification
Cools air below dew point to condense and separate water vapor
Conventional dehumidification duty in commercial and industrial spaces
Desiccant rotor dehumidification
Adsorbs moisture onto a rotating wheel and regenerates it continuously
Lower-temperature or lower-humidity targets in storage and process environments
Ultrasonic humidification
Adds fine water mist to raise or compensate relative humidity
Humidity compensation in agriculture and process areas
Application fit
Where this product can be evaluated
Application fit depends on the moisture load, operating temperature, room volume, airflow path, and installation constraints.
Step 1 — define the operating conditions. Record the temperature range, current and target relative humidity, moisture load, and the volume of the room or enclosure to be protected.
Step 2 — confirm the site constraints. Check the available power supply, drainage method, airflow or static-pressure requirement, and installation space; for ceiling, cabinet, or portable mounting confirm the fixing method and service access.
Step 3 — review the rated data and confirm the configuration. Compare the rated capacity in l/24h and the surrounding specification values in the table against the recorded conditions, then confirm the configuration with Yakeclimate before ordering.
FAQ
Frequently Asked Questions
Is the ADS-500M capacity rating based on standard testing conditions?
Rated capacity is published under the named condition in the specification table (for example 30°C/80% RH, in l/24h). Actual moisture removal depends on operating temperature, humidity, airflow, and installation conditions.
Which applications can the ADS-500M support?
The applications listed on this page are evaluation starting points. Final suitability depends on the moisture load, temperature, airflow, and installation limits of the project.
How does Yakeclimate support project configuration?
We co-develop application-specific dehumidification equipment around the operating conditions, interfaces, and integration requirements of the wider project or system.
Project support
Confirm the right configuration for your operating conditions.
Share the operating temperature, current and target humidity, room dimensions, airflow, power supply, drainage method, and installation limits. Yakeclimate can use these details to recommend a suitable next step.
